Contact Us Now

 

 

Do you find yourself interested in answers concerning Tools You Need to Install a New Bathtub ?

Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably difficult job. If the old bathtub is conveniently obtainable, the task can move quickly; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new bathtub in your restroom if you have already purchased a new tub and also do not need to alter the setup of your previous water supply pipes.
Your tools as well as product list should comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Installment

Firstly, the supporting structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last position.

 

 

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

 

 

Mounting the Tub

Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait till the bathtub has actually been made use of at least when as this will certainly settle it into its final setting.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealant can fracture rather early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I was brought to that report about A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different web page. Sharing is caring. One never knows, you will be helping someone out. We treasure reading our article about How to Install a Bathtub Yourself.

Book My Estimate